Advance Biotronics - Authorized Beckman Coulter Partner

The MicroScan autoSCAN-4 system processes panels in seconds, simplifying ID/AST while standardizing results. Over 35 years of trusted experience in reliability and conventional panel technology─with the fewest FDA limitations in automated ID/AST─make the autoSCAN-4 an ideal supplemental system for detecting difficult organisms or as a primary instrument for low-volume usage.

The MicroScan autoSCAN-4 system includes our LabPro Information Manager software and is designed to simplify workflow and minimize technologist interaction, while accommodating differing regional and institutional environments through extensive customization features. Our LabPro Alert_EXsoftware automates detection of atypical results for quick reporting and directs staff to the most appropriate action, based upon customized institutional procedures.

Operation is easy to learn and use, with minimal training
Conventional panels can be processed with direct, non-identification (ID)-dependent MICs, to help you zero in on emerging resistance
Specialty ID panels can be processed for reduced turnaround time when speed matters
Optional remote diagnostics provide an extra level of service responsiveness
Our highly rated service and support teams offer unmatched experience and expertise to ensure the optimal performance of your microbiology service

Physical	Dimensions Height: 10 in. Width: 19 in. Depth: 23 in. Weight: 40 lbs. Power cord length: 6.5 in. Cable to computer length: 8.5 in. Digital interface: RS-232C (9600 baud) AC power plug type: 5-15P
Power	Line voltage: 105/115/230 VAC ±10% Line frequency: 60/50 Hz ±10% Line current: 2.00A max. (115 V), 1.25 A max. (230 V) Heat generation: 630 BTU/HR Uninterruptible power supply (UPS): Optional
Optical System	General: Abridged filter photometer with six interference filters (wavelengths in nanometers: 440, 470, 505, 560, 590, 620), 96-channel fiber optic harness Light source: Tungsten-halogen lamp, 3500 hours Spectral bandwidth: 10 nm
Analyzer	System panel capacity: 1 panel/reading Read time: Less than five seconds
Safety Requirements	Ground impedance: 0.1 ohms maximum Dielectric withstand voltage: No dielectric breakdown (@ 1000 VAC 60 Hz for one minute) Power cord: 3-conductor, 16 AWG industrial grade SJT Overcurrent interrupter: 1.60 A (115 V), .80 A (220 V) Leakage current: Less than 500 uA
Safety Compliance The autoSCAN-4 instrument was designed and tested to comply with safety standards UL3101-1, CSA C22.2#1010.1 and EN61010-1 under the following environmental conditions:
Temperature	5˚C (41˚F) to 40˚C (104˚F)
Humidity	Maximum 80% at 31˚C (88˚F) to 50% at 40˚C (104˚F)
Altitude	Maximum 2000 m. (6,561 ft.)
Main Supply	115/230 VAC, 50/60 Hz, 230 W maximum
Overvoltage Category	Category II, connected to a branch circuit
Pollution Degree	Degree 2, normal indoor laboratory environment. Air contains only non-conductive pollutants with occasional condensation.
Emission Compliance The autoSCAN-4 instrument was designed and tested to comply with standard EN61326.
Product and Peripheral Equipment Dimensions Specifications are for autoSCAN-4 instrumentation only and do not include peripheral equipment. Dimensions for peripheral equipment are informational only and may change without notice.

Product Details

MicroScan autoSCAN-4 System

Physical

Power

Optical System

Analyzer

Safety Requirements

Safety Compliance

Temperature

Humidity

Altitude

Main Supply

Overvoltage Category

Pollution Degree

Emission Compliance

Product and Peripheral Equipment Dimensions

Company

Diagnostic Solutions

Get in Touch